The Leaders in Innovative Insulation and Corrosion Coatings
Home > Industry Uses > Architecture

Energy Star ratingArchitecture

Product Specifications

These Unitied States architectural specifications are provided for convenience and are generic in nature.


1. General

1.1 Description

Ceramic Insulation coating applied to metal, concrete, wood or other substrates where a reduction in thermal transmission is required.

Surface coating applied to substrates in fabrication shop before shipment to site, or applied on site in an approved environment during application and curing.

1.2 Quality Assurance

1. Applicator shall be certified by the coating manufacturer or distributor.

2. Finished system to conform to thermal ratings established by ASTM C236-89 (1993) e1 “Standard Test Method for Steady-State Thermal Performance of Building Assemblies by Means of a Guarded HotBox“ or equivalent.

3. Submit manufacturer’s certification that materials meet or exceed specified requirements.

1.3 Performance Requirements

1. Coating shall limit thermal transfer on all substrates

2. In addition the coating shall meet or exceed the requirements when tested in accordance with ASTM B117, C177, C411, D412, D522, D1653, D1654, D3273-82T, D3274, D4060, E84, E84-89, E96, E903-96, E1269, E1461(92), G53, or equivalents.

3. Coating should be International Codes Council approved.

4. Coating should be an approved Energy Star Partner.

5. Coating should qualify for LEED ( Leadership in Energy and Environmental Design ) points.

6. Coating should carry Factory Mutual approval

7. Coating may require USDA approval or equivalent

8. Coating may require DNV ( Det Norske Veritas ) certification

9. Coating may require IMO ( International Maritime Organization ) certification

10. Coating may require MSC ( Marine Safety Counsel ) certification

11. Coating shall exhibit good exterior UV and weathering properties to a minimum of 10 years.

1.4 Product Data

1. Submit data in accordance with Section Two which describes coating material, method of surface preparation, method of application, location of application (shop or site), environmental condition requirements \ limitations and on site touch up and protection.

1.5 Theramal Test Reports

1. Submit documented copies of thermal test reports from certified and independent thermal testing agencies .

2. Submit certified test reports of the following: Coating shall limit thermal transfer to a rating of .31 BTU per square foot / hour / F or better when tested in accordance with ASTM C236-89 (1993) e1 “ Standard Test Method for Steady-State Thermal Performance of Building Assemblies by Means of a Guarded Hot Box “ and \ or provide a significant reduction of at least 90% in BTU conduction on all substrates when tested in accordance with ASTM E1269-01 “ Standard Test Method for Determining Specific Heat Capacity by Differential Scanning Calorimetry and ASTM E1461-01 “ Standard Test Method for Thermal Diffusivity of Solids by the Flash Method “.

3. Submit copies of third party certification for R value or equivalent.

1.6 Delivery, Storage and Handling

1. Deliver coating materials to place of application in original, unopened container, bearing name of manufacturer and product identification.

2. Store materials off ground, under cover and at a temperature above freezing.

3. Transport and handle any prior coated surfaces with due care to prevent damage.


2. Products

2.1 Materials

1. Super Therm® Ceramic Insulation Coating manufactured by Superior Products International II, Inc. and distributed by Eagle Specialized Coatings And Protected Environments or equivalent, meeting the requirements of Section One preceding.

2. Super Therm® is a unique combination of high performance aliphatic urethanes, elastomeric acrylics, standard acrylics and resin additives in a water based formula.

3. Super Therm® is designed with four separate ceramic compounds for insulation from radiant heat, reflection, conduction and convection.

4. Super Therm® ceramics are not the rough multifaceted type as the one found in other coatings, Super Therm® ceramics are ground to form microscopic spheres. The spherical shape permits the 4 types of ceramics to settle very tight together, not allowing air to interact between the ceramics; thus "plating".

2.2 Certifications

1. Super Therm® meets the following ASTM certifications :

B117 450 Hour Salt Spray ( Fog ) Passed
C177 Thermal Conductivity Passed
C236-89 (93) Thermal Transmittance \ Conductance Passed
C411 High Temperature Surface Performance Passed
D412 Tensile Properties -.041 thickness = 13,248 psi Passed
D522 Mandrel Bend on metal or rubber materials -1" (25mm)
bend -1/4" (6mm) bend
Passed
D1653 Water Vapor Permeability Passed
D3273-82T Fungal Resistance Passed
D3274 Fungal Resistance Passed
D4060 Abrasion Resistance Passed
E108 Standard Test Method for Fire Tests of Roof Coverings Passed
E84 Flame Spread \ Smoke Developed - Class "A" rating
(or Class"I" or Class "1")
Passed

You may also be interested in our other solutions:

Moisture / WaterInsulation CoatingsConcrete & FlooringGraffiti
Fire & HeatCorrosionAsbestos EncapsulationEnergy SavingsIndustry